Drag to rotate
Fibre-optic video connection box · AK(S)43-4PXX
Four IP cameras over a single fibre. Power supply and protective devices are on the plate when it leaves us, the place for the switch is prepared — tested before the box leaves the works.
Five components — tap one to read about it.
Secondary 24 or 48 V · 120, 240 or 480 W
The power supply delivers 24 or 48 V on the secondary side, at 120, 240 or 480 W. There is a rule from the catalogue that goes with it: allow at least 30 % power reserve — how many cameras a power supply will carry depends on their power class.
Terminals, cable duct, tested cores
Between the power supply, the switch and the outgoing circuits there is no building site but finished wiring: terminal blocks on the rail, the cores routed in the duct and connected. The box arrives assembled, wired and tested — what remains on site is the mains connection, the fibre and the patch cables to the cameras. The switch is not included in the delivery; its place on the rail is prepared.
Splice cassette for 12 fibres · M20 entry
The link to the control centre runs over optical fibre: immune to interference, electrically isolated and good for kilometres without amplification. The splice cassette, with a splice comb for twelve fibres, sits against the right-hand inner wall, its front edge flush with the enclosure opening — separate from the active equipment and individually accessible for servicing. The fibre comes in through an M20 gland of its own; two more M20 glands stay as spares.
Swing handle or quarter-turn lock · magnetic contact
A swing handle, prepared for a half-profile cylinder, or a quarter-turn lock with double-bit operation pulls the lid against the all-round seal — both with 2-point locking. That carries IP 66 and IK 10. The contact and counter-contact of the magnetic contact sit at the top right, one on the frame and one in the lid: every opening is reported to the control room via a volt-free contact.
SPD: surge protector and circuit breaker · SO: RCBO and socket
In the SPD version, lightning and switching surges stop at the two-pole surge protector on the lower DIN rail, not at the camera; a B10 circuit breaker comes with it. The SO version carries an RCBO B16 with 30 mA and a SCHUKO service socket instead. Ethernet surge arresters for the camera lines are optional — what is fitted is stated in the test report.
The switch is not included in the delivery; its place on the rail is prepared: for an industrial PoE switch with up to six ports and up to 165 × 200 × 165 mm. For example the barox PC-PITE502-GBTE or RY-LPIGE-602GBTME.
Enclosure in polycarbonate, halogen-free, UV- and weather-resistant, in RAL 7035 (custom paint finish possible), or in stainless steel V2A / V4A. Inside, a mounting plate of galvanised steel with DIN rails and wiring ducts. Approved from −40 to +80 °C.
The mains input comes in through an M20 gland onto 4-conductor terminals with a double connection: 2 × L, 2 × N, 2 × PE. The power supply delivers 24 or 48 V on the secondary side, at 120, 240 or 480 W.
Every cable has an opening of its own, all on the underside: 4 × M20 for the mains input, the optical fibre and two spares, 4 × M25 for the LAN patch cables — with a split inner seal (IP 66) so that the RJ45 plug fits through — and two pressure-equalising elements as standard. Anything unused gets a blanking plug.
On a wall via wall angle brackets, on a pole via V2A clamping bands up to Ø 300 mm. For locations without shade the SD-V2A-ARCA4030 weather roof is available as an accessory.
Installation location
Outdoors on a wall or pole, up to 300 mm diameter.
Per data sheets 4030/PC/SPD and 4030/PC/SO · version 10.26 · subject to change
01standardDimensions
02variableMaterial
03variableLocking mechanism
01standardMounting plate
02standardCable entries underside
01not includedIndustrial PoE switch
02standardFibre connection
01standardMains input terminals 4-conductor terminals
02standardSurge arrester
03standardCircuit protection
04variablePower supply
05variableFuse terminal
06standardDouble-level terminals 2-conductor terminals
07standardTamper contact
08variableEthernet surge arrester
01standardMains input terminals 4-conductor terminals
02standardCircuit protection
03standardService socket
04variablePower supply
05variableFuse terminal
06standardDouble-level terminals 2-conductor terminals
07standardTamper contact
08variableEthernet surge arrester
We configure the box for your project — number of cameras, protective devices, mounting type, weather protection.
Hanauerstraße 15 · 75181 Pforzheim · Mon–Fri 9 am–5 pm
