InMast/250/CORE

200 watts
inside the pole.

Built for poles from 250 mm inside diameter: pushed in through the inspection opening and out of sight from outside. Inside, a power supply with 48 V and 200 W, a circuit breaker and the terminals for the mains connection — behind a cover that comes right off.

The opened box from the front: at the top a black device on a bracket, below it the blue MEAN WELL NDR-240-48 power supply, at the bottom terminal blocks and a circuit breaker — Behind the cover, from top to bottom: the device on its bracket, the NDR-240-48 power supply, terminal blocks and circuit breaker.From the side, with the cover off. A green-yellow earth conductor connects it to the body, and a black gasket runs round its inside.At an angle from the front: the depth of the box, and on the cover the two locks from the inside.

Behind the cover, from top to bottom: the device on its bracket, the NDR-240-48 power supply, terminal blocks and circuit breaker.From the side, with the cover off. A green-yellow earth conductor connects it to the body, and a black gasket runs round its inside.At an angle from the front: the depth of the box, and on the cover the two locks from the inside.

Up to eight IP cameras on one PoE switch, plus power supply, protection and mains connection — in a box that disappears inside the pole. Two locks open, cover off — and everything is in reach.

The end face of the box: a black KEL-U 16/5 frame with four small and one large light grey grommet, top right a white M12 × 1.5 fitting — The end face of the unit shown: cable entry through a KEL-U 16/5 frame with five grommets, next to it an M12 × 1.5 fitting.

Installation location

Inside the pole

Slid into an existing pole through its inspection opening.

The cover comes right off

It hangs on no hinge: release two locks and it lifts away. Its own earth conductor connects it to the body — so it stays earthed even while it lies beside the box.

Technical data

Per data sheet InMast/250/CORE · version 10.26 · subject to change

Data sheet (PDF, German)

Enclosure

01standardDimensions

Standard: 110 × 500 × 170 mm W × H × D

02variableMaterial

Opt. 01: Stainless steel V2A IP66, IK10, −40 °C … +80 °C
Opt. 02: Stainless steel V4A IP66, IK10, −40 °C … +80 °C

03variableLocking mechanism

Opt. 01: Quarter-turn lock double-bit operated, 2-point locking

Mechanical configuration

01standardMounting plate

Standard: Steel, galvanised incl. DIN rails & wiring ducts

02standardCable entry strips flange plates

Standard: 2 × cable passage 13–18 mm mains in / mains out
Standard: 2 × cable passage, double 3 mm RJ45 patch cable
Standard: 2 × cable passage 3 mm fibre in / out

Active network component

01not includedIndustrial PoE switch

Example: barox RY-LPITE-802GBTME
Example: barox LT-LPIGE-802GBTME
Example: Any active network component / switch max. 100 × 170 × 140 mm, W × H × D

02standardFibre connection

Standard: Splice cassette incl. splice comb / 12 fibres

Electrical configuration

01standardMains input terminals 2-conductor terminals

Standard: Double connection 2 × L / 2 × N / 2 × PE

02standardCircuit protection

Standard: Miniature circuit breaker type B6(A)

03standardPower supply

Standard: Secondary 48 V 200 W

Is the InMast/250/CORE right
for your site?

Tell us the number of cameras, the mounting type and the transmission — we check it and configure the box.

Send enquiry All series

Hanauerstraße 15 · 75181 Pforzheim · Mon–Fri 9 am–5 pm